Boiling Pot

Replies to This Discussion

Permalink Reply by James P on April 21, 2009 at 2:49pm

I bought that from payless plastics for $120 on special last year. They have them for $199 at the moment and were on special for $140 last month.

Just try and get one with a tap hole to make life easier.

• ▶ Reply

Permalink Reply by Reviled on April 21, 2009 at 1:40pm

Pffft, building a mash tun means work :oP Dare I say - Have you heard of BIAB? Then you dont need a mash tun just a big ass pot and $10 worth of Swiss Voile material.. Still makes awesome AG beer with minimal cost setting up, no sparging, plus you can allways look into a mash tun later if you dont like it..

www.biabrewer.info ;o)

• ▶ Reply

Permalink Reply by Dai on April 21, 2009 at 1:42pm

Check out JoKing's mash tun set up using a 38L fermenting bucket. Pure genius and I am going to copy it when I up grade my tun (barring any trade mark issues, that is).

• ▶ Reply

Permalink Reply by Steven Driessen on April 21, 2009 at 2:27pm

Intriguing... Where could I have a gander at this setup?

• ▶ Reply

Permalink Reply by Mike Neilson on April 21, 2009 at 2:28pm

Yeah look at Jokings Photos it every where!!

• ▶ Reply

Permalink Reply by Dai on April 21, 2009 at 3:03pm

Just have a look at his page- can't miss it

• ▶ Reply

Permalink Reply by JoKing on April 21, 2009 at 3:10pm

Yeah - there are heaps of shots of the setup... didn't cost too much - the kettle was the most expensive part (from trademe... look up coffee urn) The mash tun was free... there's like $20 of Gorilla Filla on it - the manifold on the inside is pretty much like James_Ps...

The HLT isn't necessary... Pump isn't necessary... JZ Whirlpool Immersion Chiller isn't necessary...

But they make brewing more gun though.

• ▶ Reply

Permalink Reply by vdog on April 21, 2009 at 1:19pm

I just wish I'd followed the advice I got when I asked a similar question 6 months or so ago, and gone really big. I got a 38L pot which is fine, but have upgraded since to a converted 50L keg which is still too small! You can always boil less in a big pot, but the reverse doesn't work so well... If I was doing it again I'd start with a 70L pot (assuming I could find one).

On a similar subject - anyone using old hot water cylinders for their HLT or brew kettle out there? What would I need to look out for if I want to do the same?

Oh, and yes - a decent chillybin will hold your mash at a fairly constant temp for that long. The bigger the volume the more constant the temperature will be - generally I drop about a degree over 75min.

• ▶ Reply

Permalink Reply by Reviled on April 21, 2009 at 1:41pm

Hey V-Dog, Barry uses two hot water cylinders for both his HLT and kettle with two electric elements, makes for a nice looking set up!

• ▶ Reply

Permalink Reply by vdog on April 21, 2009 at 2:14pm

Does it make any difference whether the cylinders are copper or stainless?

• ▶ Reply

Permalink Reply by Reviled on April 21, 2009 at 2:17pm

His are copper, stainless would be better I guess for Beer Porn, but coppers more traditional ;o)

• ▶ Reply

Permalink Reply by James P on April 21, 2009 at 2:51pm

With copper you feel more like a hill billy distiller eh Bazza?

• ▶ Reply

• ‹ Previous
• 1
• 2
• 3
• Next ›
• Page