2" Tri Clamp gaskets with one side flat to suit sanke keg - anyone know where to get these? - RealBeer.co.nz2024-03-29T10:23:31Zhttp://www.forum.realbeer.co.nz/forum/topics/2-tri-clamp-gaskets-with-one-side-flat-to-suit-sanke-keg-anyone?feed=yes&xn_auth=nojust use a std tri clamp seal…tag:www.forum.realbeer.co.nz,2013-07-29:1500433:Comment:1859252013-07-29T04:46:43.874Zdonald stewarthttp://www.forum.realbeer.co.nz/profile/donaldstewart
<p>just use a std tri clamp seal and with a sharp knife cut the ring off one side . work good for me</p>
<p>just use a std tri clamp seal and with a sharp knife cut the ring off one side . work good for me</p> Cheers for the offer James, I…tag:www.forum.realbeer.co.nz,2013-06-12:1500433:Comment:1809782013-06-12T09:17:47.319ZSamhttp://www.forum.realbeer.co.nz/profile/Sam851
<p>Cheers for the offer James, I got some EPDM ones so will stick with them for now and order some proper ones eventually (hopefully as part of another order).</p>
<p>Quite a rough finish on the epdm washer but should do for now</p>
<p>Cheers for the offer James, I got some EPDM ones so will stick with them for now and order some proper ones eventually (hopefully as part of another order).</p>
<p>Quite a rough finish on the epdm washer but should do for now</p> A EPDM is 1.50 from steel and…tag:www.forum.realbeer.co.nz,2013-06-04:1500433:Comment:1801742013-06-04T08:35:29.097ZJames Stuarthttp://www.forum.realbeer.co.nz/profile/JamesStuart
A EPDM is 1.50 from steel and tube. If you only need 1 silicon I could post you one. I have a few spares or try stilldragon ( Aussie based). They are 1.50 and good to deal with. Would prob be happy to post it out to you
A EPDM is 1.50 from steel and tube. If you only need 1 silicon I could post you one. I have a few spares or try stilldragon ( Aussie based). They are 1.50 and good to deal with. Would prob be happy to post it out to you Cheers for the help guys
I'll…tag:www.forum.realbeer.co.nz,2013-06-04:1500433:Comment:1799202013-06-04T06:00:02.045ZSamhttp://www.forum.realbeer.co.nz/profile/Sam851
<p>Cheers for the help guys</p>
<p>I'll try emailing them for a better shipping cost, but will likely try shaving a gasket as it sounds more cost effective. I've heard of people shaving the hard teflon ones (I think PTFE is teflon?) but have only seen the softer EPDM ones in stock, although if you can shave soft silicone and get a good seal sounds like I should be able to do EPDM. </p>
<p>Are you guys using a sanke as a fermenter too? I'm currently in the process of installing a corny lid in…</p>
<p>Cheers for the help guys</p>
<p>I'll try emailing them for a better shipping cost, but will likely try shaving a gasket as it sounds more cost effective. I've heard of people shaving the hard teflon ones (I think PTFE is teflon?) but have only seen the softer EPDM ones in stock, although if you can shave soft silicone and get a good seal sounds like I should be able to do EPDM. </p>
<p>Are you guys using a sanke as a fermenter too? I'm currently in the process of installing a corny lid in mine for cleaning (wasn't possible to put the corny lid in centre)</p> I've also done this to the so…tag:www.forum.realbeer.co.nz,2013-06-04:1500433:Comment:1800732013-06-04T04:00:06.610ZRichard Jackhttp://www.forum.realbeer.co.nz/profile/RichardJack
<p>I've also done this to the solid PTFE and PTFE envolope triclamp gaskets. works a treat with knife only, no problems.</p>
<p>I've also done this to the solid PTFE and PTFE envolope triclamp gaskets. works a treat with knife only, no problems.</p> You can shave one side off a…tag:www.forum.realbeer.co.nz,2013-06-04:1500433:Comment:1799852013-06-04T03:45:37.005ZJames Stuarthttp://www.forum.realbeer.co.nz/profile/JamesStuart
<p>You can shave one side off a standard silicon gasket using a sharp blade. If its still a little uneven a fine sand paper can smooth it out ( I use one like this and never had any problems)</p>
<p></p>
<p>You can shave one side off a standard silicon gasket using a sharp blade. If its still a little uneven a fine sand paper can smooth it out ( I use one like this and never had any problems)</p>
<p></p> Have you emailed and asked fo…tag:www.forum.realbeer.co.nz,2013-06-02:1500433:Comment:1796592013-06-02T03:11:09.116ZSmiffyhttp://www.forum.realbeer.co.nz/profile/PaulReginaldSmith
<p>Have you emailed and asked for a shipping cost? When I did that they came back with a much more sensible cost than was worked out automatically.</p>
<p>Have you emailed and asked for a shipping cost? When I did that they came back with a much more sensible cost than was worked out automatically.</p>